TS amplifiers
Amplifiers
TS Series is a dynamic range of 100 V 4-channel mid/high power level amplifiers meticulously designed to meet the demands of the installation market. Both, high and low impedance loads can be connected, through their input and output Phoenix connectors and output level controlled via potentiometers on the rear panel.
These amplifiers have multiple configuration possibilities such as bridge mode, subsonic filter, channel power limiter and signal link among others, in order to meet the needs of any installation. These devices also can be equipped with a GPIO connection to communicate with a third party control system.
With all these configurations TS amplifiers can meet the power requirements of any installation from 300 up to 2500 W.
Technical Data
TS-2500 |
TS-5000 |
TS-10000 |
|
| Number of channels | 4 | 4 | 4 |
| Total output power | 2500 W | 5000 W | 10000 W |
| Output power* (All ch driven / single ch) | |||
| @ 2 Ohms | 4x 312 / 1x 312 W | 4x 1250 / 1x 1250 W | 4x 2500 / 1x 2500 W |
| @ 2.67 Ohms | 4x 430 / 1x 430 W | 4x 1250 / 1x 1700 W | 4x 2500 / 1x 3300 W |
| @ 4 Ohms | 4x 625 / 1x 625 W | 4x 1250 / 1x 2500 W | 4x 2500 / 1x 2500 W |
| @ 8 Ohms | 4x 625 / 1x 1250 W | 4x 1250 / 1x 1250 W | 4x 1250 / 1x 1300 W |
| Bridge @ 4 Ohms | 2x 625 W | 2x 2500 W | 2x 5000 W |
| Bridge @ 8 Ohms | 2x 1250 W | 2x 2500 W | 2x 5000 W |
| Hi-Z 100V | 4x 625 / 1x 1250 W | 4x 1250 / 1x 2500 W | 4x 2500 / 1x 2500 W |
| Hi-Z 70V | 4x 625 / 1x 900 W | 4x 1250 / 1x 1800 W | 4x 2500 / 1x 2500 W |
| Max output voltage | |||
| 150 V peak | 150 V peak | 150 V peak | |
| Max output current | |||
| 18 A peak | 36 A peak | 50 A peak | |
| Total Harmonic Distortion | |||
| 20Hz-20KHz | <0.05% | <0.05% | <0.05% |
| Crosstalk | |||
| 20Hz-1KHz | >70 dB | >70 dB | >70 dB |
| Voltage Gain | |||
| 26 dB to 44 dB | 26 dB to 44 dB | 26 dB to 44 dB | |
| Signal to Noise Ratio | |||
| 20Hz-20KHz | 111 dBA | 111 dBA | 111 dBA |
| Required AC Mains | |||
| Operating Voltage (50Hz-60Hz) | 90V -265V AC | 90V -265V AC | 90V -265V AC |
| 1/8 Rated Power (230V, @4 Ohm) | 2.1 A | 3.7 A | 7.3 A |
| Dimmensions | |||
| W x H x D (mm) | 483 x 89 x 342 | 483 x 89 x 342 | 483 x 89 x 342 |
| W x H x D (inches) | 19 x 3.5 x 13.5 | 19 x 3.5 x 13.5 | 19 x 3.5 x 13.5 |
| Weight | |||
| Net | 7 Kg / 15.4 lbs | 7 Kg / 15.4 lbs | 7 Kg / 15.4 lbs |
| Protections | |||
|
Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, ICL™ and PCM™. |
|||
More features
Amplifier features
• Low weight high efficiency class D topology
• Universal power supply with PFC
•Up to 10000 W in 4 channels
• 8, 4 and 2 Ohm low impedance operation
• 100, 70, 50 and 35 V high impedance modes
• Power Control Management
• Phoenix connectors for inputs and outputs
• Up-side-down design to avoid fan dust accumulation
• Temperature controlled, front to back cooling
• Gain configuration from 26 to 40 dB
• GPIO for third party interface. Dante™, AES3 and Networking AES67 options
•Subsonic filter
•Signal link mini-dips configurable
• Output level control in rear panel
•Output mode configuration for high or low impedance with power limitation
Parameters configuration
Amp channel setup:
• 50Hz HP: 50Hz subsonic filter
• Output Mode: Hi impedance voltage selector. Low impedance power limitation
• Bridge mode: Low impedance bridge mode. 200V/140V high impedance mode
• Gain selection: change gain from 26dB to 40dB (2 dB steps)
Signal setup:
• Input Link: link input signal in consecutive channels
• Ouput Levels: hidden potentiometers to adjust output level
GPIO interface:
• GPI Power: turn on/off by sustained contact or sustained voltage
• GPI Mute: mute/unmute completelly amplifier by contact or voltage
• GPO Monitor: monitor each individual channel, with switching contacts for fault/OK status
