CPS-14 (64 / 96)
DSP integrated coaxial point source
Two models: CPS-14/64 & CPS-14/96
Extremely compact & powerful 3-way, tri-amplified coaxial point source element. High power 14″ neodymium transducer and a unique 1.4″ exit dual diaphgram coaxial driver.
Two models depending on coverage: CPS-14/64 (60ºH x 40ºV) or CPS-14/96 (90ºH x 60ºV).
Description
The CPS-14 is a high-output extremely compact and extremely powerful 3-way, tri-amplified DSP integrated, symmetrical Coaxial Point Source element designed for touring & fixed installations.
It uses one low distortion 14″ (4″ DUO double layer voice coil) custom speaker for the low frequencies with exclusive Malt Cross cooling technology, FEA optimized neodymium magnet circuit, aluminium demodulating ring and weatherproof cone.
For the mid/high frequencies it uses an ultra light weight 1.4″ dual diaphragm coaxial compression driver. The unique voice coil technology employs a light weight copper clad aluminium wire, wound inside and out of the Kapton former to improve heat dissipation, dramatically increasing the acoustic output and reliability of the driver while minimizes the power compression.
The larger annular midrange diaphragm covers the frequency range between 300Hz and 7KHz with a smooth, linear response. The ultra light annular diaphragm for the high frequencies offers exceptional transient response with very high efficiency from 6KHz to 22Khz.
With two subsystems in one each driver covers a smaller frequency range for increased power handling, high dynamic and extremely low distortion and delivers excellent phase coherence & perfect time alignment without problems of multi-source interference.
The 3000W 3 channel Class-D amplifier with PFC (Power Factor Correction) offers exceptional efficiency with maximum system performance whilst significantly lowering power consumption. With Thermal, short-circuit and overload protections the system module delivers superior sonic performance. Coupled together with our new generation, 64 bit/96KHz processor the system electronics are yet further guaranteed not only the utmost protection but the best performance.
Designed in-house by Lynx Pro Audio engineers our DSP offers the most recent advances in digital processing such as FIR filters delivering a linear phase & frequency response. The latest 32 bit/96KHz AD/DA converters make the system one of the most advanced & innovative point source systems on the market resulting in pristine sound quality.
A 2.8″ IPS user interface is located on the enclosure’s back panel and has multifunction joystick control enabling the user to control, select and/or adjust parameters such as cabinet presets, gain, delay and input EQ (see user manual). Two Ethernet ports enable the system to be controlled with the OCS platform for easier monitoring and processing of the system, together with the new Rainbow 3D prediction software delivers a complete system design tool.
The enclosure is made from premium grade birch plywood and finished with a polyurea coating for longer durability & weather protection.
Perfectly suited for:
| → Outdoor events | |
| → Medium sized stadiums / arenas | |
| → Auditoriums | |
| → Houses of worship | |
| → Theatres | |
| → Clubs |
Key features
|
→ Extraordinary power-to-size ratio |
|
→ Three way tri-amplified system |
|
→ 1.4” exit dual diaphragm coaxial driver |
|
→ Coaxial point source |
|
→ Ergonomic design in premium birch plywood & finished in polyurea |
|
→ Integrated Digital Processor (64 bit / 96 KHz) |
|
→ FIR linear phase filtering |
|
→ 2.8″ IPS display with multifunction joystick control |
Technical Data
Components |
LF: 1 x 14” (4” voice coil), neodymium magnet, 1000 W (AES) |
1 x 1.4″ exit dual diaphgram coaxial driver.
|
|
| Frequency Range |
55 Hz – 22 KHz (-6dB) |
Coverage |
Rotatable 60ºH x 40ºV / 90ºH x 60ºV |
| Max SPL* | Low: 130 dB / 136 dB Mid/ High: 132 dB / 138 dB |
Power amplifier |
3000 W Class D with switching power supply & PFC
|
| Processing |
Internal Lynx Processor DSPB-FL. |
Crossover |
Digital: FIR filter 600 Hz / 4500 Hz |
| Control | User control interface with 2.8” IPS screen and multifunction joystick controller |
Control connections |
USB (DSP programming) / Dual Ethernet port |
| Input |
BAL/UNBAL XLR connectors analog input AES/EBU digital input |
Nominal voltage |
100 – 240V AC @ 50-60 Hz |
| Operating voltage | 85 – 264V AC |
AC Connectors |
16A Neutrik powerCON TRUE1 TOP with looping output |
| Finish | Polyurea coating, high grade resistant paint |
Material |
15 mm premium birch plywood |
| Dimensions | 755 x 415 x 430 mm (H x W x D) |
Weight |
33 Kg (72.7 lbs) |
*Calculated maximum SPL based on rated peak power and measured sensitivity.
DSP configuration
DSP configurationDSP module configuration panel
On the back pannel of the cabinet you will find the digital control area. From the compact joystick located below the screen you are able to configure the basic adjustment functions of the internal DSP.
Just move the joystick to select the icons on the left of the screen. You can enter into the following functions: Home, settings, folder, configuration and information. Please note that you must apply the desired configuration in each one cabinet and requires electrical power to work.
If changes are not made the display will automatically dim to avoid unnecessary light in situations where light is not wanted. To re-activate the light simply press the joystick.
The following screens are an example and may vary slightly for each cabinet.
Configuration panel:
 |
HOME On the main screen you can see the cabinet’s input and output: • Input: You can see a vumeter with the input level and a clip signal. • Output: You have a vumeter with the output level (0 dBu is the amp’s maximum level) You can check the compressor and control the dynamic activity. |
 |
SETTINGS This panel allows you to change the gain, polarity, mute and the delay for the inputs. You also have the possibility of putting a high pass, changing the type of filter, frequency and order.
|
 |
FOLDER The folder screen shows you the name of the preset and its description. Using the joystick you can change the preset. |
 |
CONFIGURATION This screen is to configurate Ethernet. You can choose automatic or manual. You can also configure the screen saver. And here you have the input selection. You can choose between analog or AES3 for channel 1 or channel 2. |
 |
INFORMATION The last screen shows you some general information regarding the cabinet’s components. Here you can see the cabinet model, its serial number, DSP firmware and hardware versions, amp module model with hardware version, as well as the accelerometer status. |
Watch the following TUTORIAL to understand how it works:
DSP module configuration panel
On the back panel of the cabinet you will find the digital control area. From the compact joystick located below the screen you are able to configure the Basic adjustment functions of the internal DSP.
Just move the joystick to select the icons on the left of the screen. You can enter into the following functions: Home, settings, folder, configuration and information. Please note that you must apply the desired configuration in each one cabinet and requires electrical power to work.
If changes are not made the display will automatically dim to avoid unnecessary light in situations where light is not wanted. To re-activate the light simply press the joystick.
The following screens are an example and may vary slightly for each cabinet.
HOME
On the main screen you can see the cabinet’s input and output.
• Input: You can see a vumeter with the input level and a clip signal.
• Output: You have a vumeter with the output level (0 dBu is the amp’s maximum level) You can check the compressor and control the dynamic activity.
SETTINGS
This panel allows you to change the gain, polarity, mute and the delay for the inputs.
You also have the possibility of putting a high pass, changing the type of filter, frequency and order.
FOLDER:
The folder screen shows you the name of the preset and its description.
Using the joystick you can change the preset.
CONFIGURATION:
This screen is to configurate Ethernet. You can choose automatic or manual. You can also configure the screen saver.
And here you have the input selection. You can choose between analog or AES3 for channel 1 or channel 2.
INFORMATION:
The last screen shows you some general information regarding the cabinet’s components.
Here you can see the cabinet model, its serial number, DSP firmware and hardware versions, amp module model with hardware version, as well as the accelerometer status.
Watch the following TUTORIAL to understand how it works:
More features
Hardware for CPS-14
 |
EnclosureThe CPS-14 cabinet is constructed from 11-ply premium birch plywood (15mm thickness) and finished with polyurea coating |
 |
Internal designThe internal structure of the CPS-14 is heavily braced for greater longevity and all parts are assembled on metal inserts with metric screws. The amplification modules & DSP are housed in a separate chamber to the drivers avoiding excessive heat & vibration, thus delivering greater efficiency and reliability. |
 |
Rear panelThe powder coated steel rear panel contains all connections and houses the CPS-14 amplification modules and DSP, is easily accessible and housed separately from the drivers for increased reliability and efficiency |
 |
GrillThe CPS-14 has two heavy duty, powder coated front grille with a special acoustic rear fabric to protect the transducers against dust and dirt. The medium frequencies grille uses a magnetic attachment system that can be removed for easy access and rotation of the diffuser. |
 |
HandlesThe CPS-14 has two ergonomic handles with firm internal grip to facilitate transport, positioning and loading of the cabinets. Both handles are placed at the top and bottom of the cabinet. |
Rear image
Accessories for CPS-14
 |
AGR-10 Eye bolt for CPS-14 |
 |
SC-FC1 Lightweight install stud for CPS-14 |
 |
UBR-HCPS14 Horizontal U bracket for CPS-14 |
 |
UBR-VCPS14
Vertical U bracket for CPS-14
|
 |
FD-1CPS14NL Rain cover for CPS-14 |
 |
FD-CPS14 Nylon protection for CPS-14 |
 |
DI-1464C Rotatable horn for CPS-14/64 |
|
DI-1496C Rotatable horn for CPS-14/96 |
